Fusion 360 Changing Dimensions of a Uploaded Shape
This postal service is a quick Fusion 360 CAM tutorial & introduction. We will look at how to create the start setup and a couple of the rocker arm paths. We will then open the completed toolpaths to run a simulation and postal service process.
The rocker arm requires three setups to auto using 2.five axis machining techniques. We will create setup i and two of the toolpaths for the setup. Then we will open up a finished version to review all iii setups.
Setup 1
Setup ii
Setup 3
Upload Fusion 360 Information
Yous will use the data panel to upload a Fusion 360 design and CAM toolpaths. Click Open Data Panel to brandish the data console.
Fusion uses projects to organize designs and related data. Select the desired projection from the drop-down, and so click Upload to select the files.
Click Select Files, then browse to the location where you downloaded the files attached to this postal service. Select rocker arm.f3d and rocker arm FINAL.cam360, then click Open. Click Upload to begin the upload process. The files are uploaded to your A360 hub.
A dialog is displayed to show the progress of the upload and translation process. Y'all can shut this dialog and proceed working in Fusion while the file processes.
Get to the Fusion 360 CAM Workspace
When the upload is complete, the files are listed in the information panel. Close the Upload progress dialog.
Right-click on the thumbnail and select Open to open up the uploaded pattern.
The rocker arm Fusion design is opened. We desire to create toolpaths on this 3D design. Click File > New Toolpath from Design.
Create a Setup
You are taken to the CAM workspace with the rocker arm design loaded. The first footstep is to create a setup then define the stock size and orientation: Orient, the model as shown.
In the Browser, click Change Active units and select Inch.
Click Setup to define the stock size and orientation.
Click Stock Betoken, so select the upper right stock point to move the triad.
Click the Caput of the blue arrow to flip it upwardly. Verify that the bluish arrow (Z-axis) is pointing up, the green arrow (Y-axis) is pointing to the correct, and the red arrow (Ten-axis) is pointing towards you lot.
Click the Stock tab to define the stock size.
- Modify Mode to Relative size box.
- Stock Side Offset: 0.fifteen in
- Stock Meridian Offset: 0.5 in
- Stock Lesser Offset: 0.5 in
Click OK to finish the setup.
Create a Face Performance
Now we will define ii toolpaths to show how this works in Fusion 360. Beginning by clicking the Face command.
Click Select adjacent to Tool to pick the tool to use.
Currently, the Windows and Mac interfaces for the tool library are unlike. Both libraries are shown below. Select the 2" Face Mill.
Windows:
Mac:
Click OK to cease the toolpath definition.
Create a Clearing Performance
Click 2d Adaptive Clearing to begin defining the 2nd CAM toolpath.
Click Select next to Tool to choice the tool to use.
Select a Apartment Finish Factory with a 0.five in diameter and a Flute Length greater than 2 in.
Windows
Mac
Click the Geometry tab, so select Pocket Pick. Click the height outside border of the part.
Click the Heights tab. Set up the Bottom Height to Model lesser, and so set the Commencement to -0.05 in.
Click OK to complete the operation.
Simulate CAM Toolpaths
At present we volition review the completed toolpaths, simulate the operations, and post the NC code. In the Data Panel, right-click on rocker arm Final and select Open up. This loads the rocker arm with the 3 completed setups.
Orient, the model as shown and select Setup 1 in the Browser.
Click Simulate.
Enable Stock in the Simulate dialog box, then click the Start the Simulation button at the awarding's bottom. The operations in Setup 1 are simulated. You can step frontwards and back or change the speed of the simulation. Close the dialog box when washed.
Select all 3 setups, and so click Post Process.
Click OK to the warning nearly multiple WCS.
In the Post Process dialog box:
- Prepare Post Configuration to haas.cps – Generic HAAS.
- Set Program name or number to 1234.
- Click OK
Enter 1234 in the Relieve As field and click Save to proper name the file.
Review the code in the NC Editor, then click Close.
You're done! In this mail service, we have:
- Created a setup.
- Created two toolpaths for that setup.
- False the completed setups.
- Generated the NC code for the toolpaths.
This should get you started with what's possible using the Fusion 360 CAM workspace. Check the Fusion help site or cam.autodesk.com for more than information. Learn more near the Fusion 360 Machining Extension here.
Source: https://www.autodesk.com/products/fusion-360/blog/getting-started-introduction-to-cam-and-toolpaths/
0 Response to "Fusion 360 Changing Dimensions of a Uploaded Shape"
Post a Comment